Send Message

How to Choose A Right Fusion Splicer?

August 16, 2019

Latest company news about How to Choose A Right Fusion Splicer?

 

                                     latest company news about How to Choose A Right Fusion Splicer?  0

Optical fiber fusion splicer  is mainly used for optical cable construction and maintenance in optical communication, so it is also called  fusion splicer.

 

The optical fiber fusion splicers can also be classified as mechanical optical fiber fusion splicer and heating-type fiber fusion splicer by its working method. Freeze welding has the advantages of rapid construction, easy operation and so on.

 

At the same time, there are also these disadvantages: two optical fibers need to be prepared in the field, and the construction strength is large; the connection performance is completely dependent on the matching liquid, and the coating layer does not meet the requirements of the site.

 

Heat welding, the optical fiber will not be bent under the protection and fixation of the tail sheath and has the advantages of good continuity, high stability and long service life.

 

The optical fiber fusion splicers can be classified as multi-mode and single-mode fiber fusion splicer by spliced fiber category. Different types of optical fibers have greater differences in the requirements of the fusion splicer's structure and optical fiber alignment accuracy.

 

The general working principle is using a high-voltage arc to melt the two fiber sections while gently propelling the two fibers into one with a high-precision motion mechanism to achieve coupling of the fiber mode field.

 

 

 The general multi-mode fusion splicer cannot be used for single-mode optical fiber fusion. The single-mode fusion splicer can be used for multi-mode optical fiber fusion splicing by changing the welding parameters. This is because the fiber alignment methods of the multimode and single mode fiber fusion splicer are different.

 

The fiber alignment method of the multimode fiber fusion splicer uses the alignment of the cladding alignment(125μm); the fiber alignment of the single mode fiber fusion splicer The method uses the core alignment. Since the mode field diameter of the single mode fiber core is very small, only 1/5 of the multimode (810 microns), the core alignment method is required to have high precision.

 

 

However, it also has the following deficiencies:

 

The fiber is easy to break during the plugging and unplugging process of the connector; after testing the tailings of the fusion-splicer, it will be scrapped if it is not well cut and the cost is high; if the connection is unsuccessful, it cannot be reused.

 

 optical fiber fusion splicer

 

Nowadays,by analyzing the working method of different optical fiber fusion splicers and considering the working

 

environment,we can easily distinguish which kind of splicer is the most appropriate for us. 

 

 

Connection method

Heat welding

(permanent)

freeze welding

(emergency)

active connection
Method

welding Spot fusion

by discharging

fixing and bonding

two fibers together by

mechanochemistry

Using various fiber

optic connection

devices to connect

sites to sites or sites

to fiber optic cables

Application

Generally used in the

long-distance

connection,

permanent or

semi-permanently

fixed connection

Emergency

construction

Inside a building
Loss Value 0.01-0.03dB/point >0.1dB >1dB
Advantages

Permanency、Low

Loss Value

fast connection for

emergency use in a

short time

flexibility & simplicity
Disadvantages

highly Dependent on

the performance

of the machine

instability after

long-term use、

highly increasing

attenuation

huge attenuation

 

About freeze welding

 

1. Great dependence on cutting quality during construction;

 

2. The cutting length has a great anthropogenic influence on the fiber connection characteristics;

 

3. Connector performance indicators cannot be factory tested (IL, RL);

 

4. The concentricity and repeatability of the optical fiber and the ferrule is poor (the difference in the size of the field fiber is 122um~126um);

 

5. The bare quartz fiber is exposed and the product life is short;

 

6. In addition to insertion loss (IL) and return loss (RL) indicators, conventional connectors also have mechanical specifications of the product: the radius of curvature of the connector end face, the eccentricity rate and Subsidence rate of the optical fiber. But also because of these indicators, it is guaranteed that the performance specification of the connection between any two connectors is good; but all this is guaranteed by grinding; the straight-through fiber structure cannot be guaranteed, so it is difficult to ensure the repeatability of the fiber connection;

 

 

7. It relies on the light source, optical power meter, and other equipment to ensure the quality of the connection, increasing the cost of test equipment, test time and labor;

 

8. The performance index of Insertion loss (0.3dB) and return loss (UPC, 45dB) are not good.They can not meet the high return loss (APC) demand;it is difficult to meet future system high-speed requirements and system expansion requirements (1: 32-1:64-1:128);

 

 

9. Poor stability, increase the follow-up maintenance costs;

 

About Heat welding

 

1.FTTH hot melt solution for indoor fiber fusion bonding multi-energy fusion spathe icer With Customized the hot melt quick connector SC, FC, LC.

 

2.The simple and quick operation, the high success rate of the connection, lower maintenance costs.

 

3.Long service life, good reliability, reduced maintenance costs, improved network stability, good optical performance indicators, and reduced reinvestment of future network commissions

 

4. The traditional fusion splicer is bulky and requires many accessories.It is complicated in operation and is not easy to carry

 

5. Multi-functional micro-computer of the equipment is light and high, suitable for distributed operations, and other work environment operations, suitable for on-site operations for convenient Cutting, welding, cleaning, heat shrinking.

 

6.Less human factors and no special training

 

7.No need for separate splice protection, fiber length can be effectively controlled

 

8. Meet various requirements, UPC, APC, FC SC LC 3mm sheath cables, etc.

 

9. Short stay in the room, quick and concise operation process, does not infringe the privacy of residents

 

10.Reduce other equipment costs by reducing tooling such as testing. Minimum number of construction staff to reduce construction costs.

 

11. Not affected by the external environment, high opening rate, lower maintenance costs.

 

So,It’s no doubt that using fiber Fusion Splicer is a more efficient and quality- guaranteed way to finish the optic fiber welding work. With following merits of our fiber optic fusion splicer,you will half complete the work with double results.

 

 

l 4.3-inch Color LCD monitor

l Applied for Fibers, Cables and SOC (splice- on connector)

l Integrated Holder Design

l USB&DC interface

l Compact & Light weight

l Fully Automatic, Semi-automatic and Manual Operation

l Shockproof, Drop resistance

l Power saving Function

Get in touch with us
Contact Person : Mrs. Yvone Si
Tel : 86-13480892975
Fax : 86-755-23036652
Characters Remaining(20/3000)